China Professional Roller Chain for Transmission Machine From China Manufacturer (ISO)

Product Description

OUR PRODUCTS LIST:
A and B series single/double/triple standard roller chain and no-standard roller chain

DIN/ISO	ANSI	Pitch	Roller	Width	Pin	Pin		Lnner	Plate	Ultimate	Average	weight
KIN/ISO	ANSL			between	diameter	length		plate	thick	tensile	tensile	per
Chain	Chain			inner plates				depth	-ness	strength	strength	meter
No.	No.	P	d1	b1	d2	L	Lc	h2	T	Q	Q0	q
		P	max	min	max	max	max	max	max	min	Q0	q
		mm	mm	mm	mm	mm	mm	mm	mm	kN/LB	kN	kg/m
*03C	*15	4.7625	2.48	2.38	1.62	6.1	6.9	4.3	0.6	1.80/409	2	0.08
*04C-1	*25	6.35	3.3	3.18	2.31	7.9	8.4	6	0.8	3.50/795	4.6	0.15
*06C-1	*35	9.525	5.08	4.77	3.58	12.4	13.17	9	1.3	7.90/1795	10.8	0.33
085-1	41	12.7	7.77	6.25	3.58	13.75	15	9.91	1.3	6.67/1516	12.6	0.41
08A-1	40	12.7	7.95	7.85	3.96	16.6	17.8	12	1.5	14.10/3205	17.5	0.62
10A-1	50	15.875	10.16	9.4	5.08	20.7	22.2	15.09	2.03	22.20/5045	29.4	1.02
12A-1	60	19.05	11.91	12.57	5.94	25.9	27.7	18	2.42	31.80/7227	41.5	1.5
16A-1	80	25.4	15.88	15.75	7.92	32.7	35	24	3.25	59.70/12886	69.4	2.6
20A-1	100	31.75	19.05	18.9	9.53	40.4	44.7	30	4	88.50/20114	109.2	3.91
24A-1	120	38.1	22.23	25.22	11.1	50.3	54.3	35.7	4.8	127.00/28864	156.3	5.62
28A-1	140	44.45	25.4	25.22	12.7	54.4	59	41	5.6	172.40/39182	212	7.5
32A-1	160	50.8	28.58	31.55	14.27	64.8	69.6	47.8	6.4	226.80/51545	278.9	1.1
36A-1	180	57.15	35.71	35.48	17.46	72.8	78.6	53.6	7.2	280.20/63682	341.8	13.45
40A-1	200	63.5	39.68	37.85	19.85	80.3	87.2	60	8	353.80/80409	431.6	16.15
48A-1	240	76.2	47.63	47.35	23.81	90.5	103	72.39	9.5	51.30/115977	622.5	23.2

DIN/ISO	Pitch	Roller	Width	Pin	Pin		Lnner	Plate	Ultimate	Average	weight
KIN/ISO			between	diameter	length		plate	thick	tensile	tensile	per
Chain			inner plates				depth	-ness	strength	strength	meter
No.	P	d1	b1	d2	L	Lc	h2	T	Q	Q0	q
	P	max	min	max	max	max	max	max	min	Q0	q
	mm	mm	mm	mm	mm	mm	mm	mm	kN/LB	kN	kg/m
04B-1	6	4	2.8	1.85	6.8	7.8	5	0.6	3.2/682	3.2	0.11
05B-1	8	5	3	2.31	8.2	8.9	7.1	0.8	5.0/1136	5.9	0.2
*06B-1	9.525	6.35	5.72	3.28	13.15	14.1	8.2	1.3	9.0/2045	10.4	0.41
08B-1	12.7	8.51	7.75	4.45	16.7	18.2	11.8	1.6	18.0/4091	19.4	0.69
10B-1	15.875	10.16	9.65	5.08	19.5	20.9	14.7	1.7	22.4/5091	27.5	0.93
12B-1	19.05	12.07	11.68	5.72	22.5	24.2	16	1.85	29.0/6591	32.2	1.15
16B-1	25.4	15.88	17.02	8.28	36.1	37.4	21	4.15/3.1	60.0/13636	72.8	2.71
20B-1	31.75	19.05	19.56	10.19	41.3	45	26.4	4.5/3.5	95.0/21591	106.7	3.7
24B-1	38.1	25.4	25.4	14.63	53.4	57.8	33.2	6.0/4.8	160.0/36364	178	7.1
28B-1	44.45	27.94	30.99	15.9	65.1	69.5	36.7	7.5/6.0	200.0/45455	222	8.5
32B-1	50.8	29.21	30.99	17.81	66	71	42	7.0/6.0	250.0/56818	277.5	10.25
40B-1	63.5	39.37	38.1	22.89	82.2	89.2	52.96	8.5/8.0	355.0/80682	394	16.35
48B-1	76.2	48.26	45.72	29.24	99.1	107	63.8		560.0/127272	621.6	25

Products show

Our workshop

Our hot treatment equipment

FAQ

Q1. What is your terms of packing?
A: Generally, we pack our goods in single color box. If you have special request about packing, pls negotiate with us in advance, we can pack the goods as your request.

Q2. What is your terms of payment?
A: T/T 30% as deposit, and 70% before delivery. We’ll show you the photos of the products and packages
before you pay the balance. Other payments terms, pls negotiate with us in advance, we can discuss.

Q3. What is your terms of delivery?
A: EXW, FOB, CFR, CIF.

Q4. How about your delivery time?
A: Generally, it will take 25 to 30 days after receiving your advance payment. The specific delivery time depends
on the items and the quantity of your order.

Q5. Can you produce according to the samples?
A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.

Q6. What is your sample policy?
A: We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and
the courier cost.We welcome sample order.

Q7. Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery

Q8: How do you make our business long-term and good relationship?
1. We keep good quality and competitive price to ensure our customers benefit ;
2. We respect every customer as our friend and we sincerely do business and make friends with them,
no matter where they come from.

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Material:	Alloy
Structure:	Roller Chain
Surface Treatment:	Polishing
Chain Size:	P200
Feature:	Fire Resistant, Oil Resistant, Heat Resistant
Transport Package:	Non-Fumigation Wooden Box, by Air, by Ocean

Samples:	US$ 2/Meter 1 Meter(Min.Order) \| Request Sample

Customization:	Available \| Customized Request

transmission chain

How does the design of a transmission chain impact its efficiency?

The design of a transmission chain plays a crucial role in determining its efficiency and overall performance. Here’s a detailed explanation:

1. Link Shape and Geometry: The shape and geometry of the chain links directly affect the efficiency of power transmission. Chains with optimized link designs, such as streamlined or curved profiles, reduce friction and minimize energy losses during operation. These design features enhance the chain’s efficiency and contribute to smoother power transfer.

2. Bearing Surfaces: The design and quality of bearing surfaces in a transmission chain significantly impact its efficiency. Well-designed chains incorporate precision-machined bearing surfaces that minimize friction and wear. Smooth and accurately machined surfaces reduce energy losses caused by friction, resulting in higher efficiency and improved overall performance.

3. Roller and Bushing Design: The design of the rollers and bushings in a transmission chain can greatly influence its efficiency. Chains with properly designed rollers and bushings reduce friction and enable smooth rotation. Low-friction contact surfaces between the rollers and sprockets ensure efficient power transmission, reducing energy waste and improving the overall efficiency of the chain.

4. Lubrication System: The design of the lubrication system within the chain also affects its efficiency. Proper lubrication reduces friction and wear, allowing the chain to operate more efficiently. Some transmission chains incorporate self-lubricating features or advanced lubrication mechanisms to ensure optimal lubrication throughout the chain, further improving efficiency.

5. Material Selection: The choice of materials for the chain’s components, such as links, rollers, and bushings, impacts its efficiency. High-quality materials with excellent wear resistance and low friction coefficients contribute to higher efficiency. Additionally, lightweight materials can reduce the overall weight of the chain, resulting in lower inertia and improved efficiency.

6. Precision Manufacturing: The precision and accuracy with which a transmission chain is manufactured can directly affect its efficiency. Chains produced with tight tolerances and high-quality manufacturing processes ensure proper fit, reduced friction, and optimal power transfer, resulting in improved efficiency.

It is important to note that the design considerations and features mentioned above can vary depending on the specific type and application of the transmission chain. Consulting with experts or manufacturers can provide further insights into the design features that optimize efficiency for a particular transmission chain.

transmission chain

Can transmission chains be used in renewable energy systems?

Yes, transmission chains can be used in renewable energy systems. Here’s a detailed answer to the question:

Renewable energy systems, such as wind turbines and solar power plants, often require the efficient transfer of mechanical power from the energy source to the generator or other components. Transmission chains play a vital role in this power transmission process.

In wind turbines, transmission chains are commonly used in the pitch control system. The pitch control mechanism adjusts the angle of the turbine blades to optimize their performance based on wind conditions. Transmission chains provide a reliable and robust method for transmitting the necessary power from the pitch motor to the blade adjustment mechanism.

In solar power plants, transmission chains are used in solar tracking systems. These systems allow solar panels or mirrors to track the sun’s movement throughout the day, maximizing the amount of sunlight captured and improving the overall efficiency of the solar power generation. Transmission chains facilitate the precise movement required for solar tracking, ensuring accurate alignment and optimal energy capture.

Transmission chains used in renewable energy systems need to be durable, reliable, and capable of withstanding the environmental conditions typically encountered in these applications. They may require specific features such as corrosion resistance, high strength, and the ability to operate in a wide range of temperatures.

Overall, transmission chains offer an efficient and effective solution for power transmission in renewable energy systems. Their versatility, reliability, and ability to handle various loads and speeds make them suitable for use in wind turbines, solar tracking systems, and other renewable energy applications.

transmission chain

Can transmission chains be used in high-speed applications?

Yes, transmission chains can be used in high-speed applications, but there are certain considerations to take into account. Here’s a detailed explanation:

1. Chain Design: High-speed applications require transmission chains that are specifically designed to withstand the increased rotational speeds and dynamic loads. These chains often have features such as specialized surface treatments, high-quality materials, and precision manufacturing to ensure smooth operation at high speeds.

2. Lubrication: Proper lubrication is crucial in high-speed applications to minimize friction, heat generation, and wear. Lubricants with excellent high-speed characteristics, such as low viscosity and high film strength, are typically recommended. In some cases, specialized lubrication systems, such as oil circulation or spray lubrication, may be used to ensure sufficient lubrication at high speeds.

3. Balancing: High-speed operation can induce vibration and imbalance in transmission chains, leading to increased stress and potential failure. Balancing the chain and associated components, such as sprockets and shafts, is important to minimize vibration and ensure smooth operation at high speeds.

4. Tensioning: Proper tensioning of the transmission chain is crucial in high-speed applications. Maintaining the appropriate tension helps prevent chain slippage, excessive vibration, and premature wear. Tensioning devices, such as automatic tensioners or spring-loaded systems, may be used to ensure optimal tension throughout the operation.

5. Maintenance: Regular inspection, lubrication, and maintenance are vital in high-speed applications to detect any potential issues and address them promptly. Periodic checks for wear, proper alignment, and lubrication effectiveness can help prevent unexpected failures and ensure the reliable performance of transmission chains.

It is important to consult with manufacturers or industry experts to select the appropriate transmission chain that is specifically designed and rated for high-speed applications. By following the recommended guidelines and maintenance practices, transmission chains can reliably and safely operate in high-speed environments, meeting the performance requirements of such applications.

China Professional Roller Chain for Transmission Machine From China Manufacturer (ISO)
editor by CX 2024-05-13

China Standard Rivetless Drop Forged Conveyor Link X458 Chain for Painting Line System

Product Description

About Factory

With more than 18 years’ histiory, we are a professinal manufacturer for drop forged products such as forged chain (X348 X458 X658 X678 X698 F100 F160), scraper chain (10160, 14218, 14226, 142N), conveyor trolley (X348, X458, X678, XT160), and drive chain (X348, X458, X678), and so forth standard moulds of chain.

Besides, we can also produce as per your drawing or sample, special link chain, pusher, pin and plate, according to customers’ unique requirements.

Product Description

1) Material: Alloy steel, 40Cr, 42CrMo and so on.
2) Types: X348 X458 X658 X678 X698 F100 F160, and so on. (Or as per your drawing)
3) Process: Moulding→Forging→Polishing & Blasting→Fine machining→Heat treatment→Blasting→Inspecting & testing→Packing

Product Show

Technical Data

Model	Pitch	Dimension						Lateral Corner	Standard Measured Length (mm)	Measured Quantity	Tensile Strength (KN)	Weight (Kg/m)
Model	Pitch	A	F	G	J	K	S	Lateral Corner	Standard Measured Length (mm)	Measured Quantity	Tensile Strength (KN)	Weight (Kg/m)
80H	80	73	42	18.4	20	34.5	19.5	7	3032/3058	38	250	7.8
X348	76.6	46	27	12.7	12.7	20.6	13.5	9	3050.5/3095.2	40	110	3.2
X458	102.4	57	37	16	16	26.5	17.5	9	3063.1/3090.2	30	210	5.2
468H	102.4	84.1	47.8	18	29.5	42.9	22.2	9	3063.1/3090.2	30	318	11.5
X658	153.2	55.6	35	16	16	57.2	17.5	7	3055.1/3082.8	20	210	4
X678	153.2	77	50.8	22.2	21	34.2	25	7	3055.1/3082.8	20	320	9.5
678	153.2	77	50.8	22.2	21	34.2	25	7	3055.1/3082.8	20	320	9.5
698	153.2	95.25	64	28	25.4	41.3	32	5	3055.1/3082.8	20	515	17
998	229.4	95.25	67.5	28	25.4	41.3	32	5	3205/3232.4	13	515	14.8
9118	229.4	123.8	76.2	35	33.5	52	38.1	5	3205/3232.4	13	832	24.2
S348	76.6	38.9	28.6	12.7	12.7	20.6	13.5	9	3050.5/3095.2	40	110	3.2
S458	102.4	52.1	35	16	16	26.5	17.5	9	3063.1/3090.2	30	210	5.2
S678	153.2	69.8	50.8	22.2	21	34.2	25	7	3055.1/3082.8	20	320	9.5
S698	153.2	73	68.3	28	25.4	41.3	32	5	3055.1/3082.8	20	515	17
S9118	229.4	98.4	77.8	35	33.5	52	38.1	5	3205/3232.4	13	832	24.2
F100	100	57	37	16	16	26.5	17.5	9	2991.3/3018.3	30	210	5.2
F160	160	78	54	24	20.5	36	28	7	3190.7/3219.5	20	318	10.3

Products & Testing Equipments

Products Application

Packing & Delivery

Why Choose Us?

1. We are engaged in chain industry over 15 years with rich market experience. We keep improving production techniques. All the products have longer working life and have passed the market test.

2. We can design the correct chains with high quality material, good abrasion resistance, good corrosion, high strengthen and etc as per your request or the chain application.

3. We are the chain manufacturer; you can directly purchase the product from us with low price and high quality.

4. We have a professional team for international trade, they have abundant experiences and are always ready to solve problems for customers. So you have nothing to worry about.

5. We have the long-term cooperative forwarder who can give us the lowest freight. And it can help you to save the freight. What’s more, for the FCL, we will design the packages as per the container sizes with the largest capacity to save the shipping cost for both of us.

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Material:	Alloy
Structure:	Combined Chain
Surface Treatment:	Polishing

Samples:	US$ 5/Piece 1 Piece(Min.Order) \| Order Sample

Customization:	Available \| Customized Request

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost: Estimated freight per unit.	about shipping cost and estimated delivery time.

Payment Method:
	Initial Payment Full Payment

Currency:	US$

Return&refunds:	You can apply for a refund up to 30 days after receipt of the products.

conveyor

What are the benefits of using a silent conveyor chain?

A silent conveyor chain, also known as a noise-reducing conveyor chain, offers several advantages in conveyor system applications:

1. Noise Reduction:

– One of the primary benefits of using a silent conveyor chain is the significant reduction in noise levels. These chains are specifically designed to minimize the noise generated during operation, creating a quieter and more comfortable working environment.

2. Improved Work Environment:

– By reducing noise levels, a silent conveyor chain contributes to a better work environment, particularly in settings where noise reduction is important, such as manufacturing facilities, warehouses, and distribution centers. It helps reduce employee fatigue, enhances communication, and improves overall worker satisfaction.

3. Compliance with Noise Regulations:

– In some industries or regions, there are specific noise regulations that must be met. Using a silent conveyor chain helps ensure compliance with these regulations, avoiding potential penalties and legal issues.

4. Increased Productivity:

– A quieter working environment created by a silent conveyor chain can lead to increased productivity. With reduced noise distractions, employees can focus better on their tasks, resulting in improved efficiency and output.

5. Extended Chain and Equipment Life:

– Silent conveyor chains are often designed with advanced materials and technologies that offer enhanced wear resistance and durability. They can withstand heavy loads, reduce friction, and minimize wear and tear on both the chain and the associated equipment, resulting in longer service life and reduced maintenance costs.

6. Versatility:

– Silent conveyor chains are available in various configurations and designs, making them compatible with a wide range of conveyor systems and applications. They can be used in different industries, including automotive, food processing, packaging, and more.

When considering a silent conveyor chain, it is important to consult with a reputable chain manufacturer or supplier to ensure the chain meets the specific requirements of the application.

conveyor

How does a conveyor chain contribute to overall production efficiency?

A conveyor chain plays a crucial role in enhancing overall production efficiency in various industries. Here are the ways in which it contributes to efficiency:

1. Continuous Material Flow: A conveyor chain enables continuous and uninterrupted material flow from one point to another. It eliminates the need for manual handling or transportation of goods, reducing downtime and delays in production processes.

2. Increased Throughput: By automating material handling, a conveyor chain enables faster and more efficient movement of goods. It allows for higher throughput and production rates, maximizing the utilization of resources and reducing cycle times.

3. Improved Productivity: With a conveyor chain, employees can focus on value-added tasks rather than manual material handling. This leads to improved productivity as workers can concentrate on more skilled and critical operations.

4. Efficient Resource Allocation: A well-designed conveyor chain system optimizes the utilization of space, allowing for efficient layout and organization of production areas. It helps in streamlining workflow and minimizing wastage of resources such as floor space, manpower, and equipment.

5. Quality Control: Conveyor chains can be integrated with inspection stations or automated processes to ensure quality control at various stages of production. This helps in detecting and rectifying any defects or inconsistencies, reducing the chances of faulty products reaching the market.

6. Reduced Material Handling Costs: By eliminating or minimizing manual material handling, a conveyor chain reduces labor costs associated with transportation, lifting, and carrying of goods. It also minimizes the risk of injuries or accidents related to manual handling.

7. Flexibility and Adaptability: Conveyor chains can be customized to suit specific production requirements. They can be designed to accommodate different types of products, handle various load capacities, and adapt to changes in production demands. This flexibility allows for seamless integration with existing production systems and easy scalability.

8. Safety and Ergonomics: Conveyor chains incorporate safety features such as guards, emergency stop buttons, and interlocks to ensure worker safety. They also promote ergonomic practices by reducing physical strain on workers and minimizing the risk of musculoskeletal injuries.

Overall, a well-designed and properly maintained conveyor chain system enhances production efficiency by optimizing material flow, increasing throughput, improving productivity, reducing costs, ensuring quality control, and prioritizing worker safety.

conveyor

Can a conveyor chain be used in high-temperature environments?

Yes, conveyor chains can be designed and used in high-temperature environments, but it depends on the specific type of chain and the temperature range involved. Here are some key considerations:

Material Selection: Conveyor chains for high-temperature applications are typically made from heat-resistant materials such as stainless steel or alloy steels that can withstand elevated temperatures without significant degradation.
Lubrication: Proper lubrication is essential in high-temperature environments to minimize friction and wear. Special high-temperature lubricants are available that can withstand the operating temperatures and provide effective chain lubrication.
Chain Design: Chains used in high-temperature environments may have specific design features to accommodate thermal expansion and minimize the risk of binding or seizing. These can include increased clearances, special joint designs, or heat-resistant coatings.
Temperature Limitations: Each conveyor chain has a maximum temperature limit specified by the manufacturer. It is important to consider this limit and ensure that the operating temperature does not exceed it to maintain the integrity and performance of the chain.
Proper Maintenance: Regular inspection and maintenance are crucial in high-temperature applications. This includes monitoring chain wear, lubrication levels, and any signs of heat-induced damage or degradation.

However, it is important to note that the suitability of a conveyor chain for high-temperature environments ultimately depends on the specific operating conditions, including the temperature range, duration of exposure, and the application requirements. It is recommended to consult with the chain manufacturer or an experienced engineer to select the appropriate chain and ensure its safe and reliable operation in high-temperature environments.

China Standard Rivetless Drop Forged Conveyor Link X458 Chain for Painting Line System
editor by CX 2024-05-13

China OEM 500 Chain Sprocket Mini Excavator Crawler Undercarriage Spare Parts Track Bottom Roller Sprocket

Product Description

Detailed Photos

Product Description

Product Name	Sprocket/Drive Sprocket
Type	Excavator Spare Parts
Model Number	PC100-5/6 PC120 PC130
Material	50Mn
Surface Hardness	HRC50-56
Country of CZPT	ZheJiang China
MOQ	1pcs

Company Profile

Xihu (West Lake) Dis. Dingrui Construction Machinery Co., Ltd. is a construction machinery parts enterprise that integrates the design and development, manufacturing and technical service of excavator parts.We specialise in the development, production and sale of excavator parts and are committed to providing our global customers with products and services of outstanding quality and consistent performance.

For the future, Dingrui will always adhere to the corporate mission of “providing excellent products and services to global customers”, abide by the core values of “integrity, enterprise, symbiosis and innovation”, continuously strengthen research and development innovation and talent team construction, continuously promote the standardization, standardization and scientific management, and commit to become a globally trusted construction machinery parts life-cycle service provider!

Packaging & Shipping

FAQ

Q1: You are a trader or a manufacture?
A1: We are a factory-based and trade integration company. Our factory is located in No. 65, Dawei Village Industrial Zone, Huanfeng Town, Xihu (West Lake) Dis. County, HangZhou City, ZheJiang Province.
Q2: How can I be sure the part will fit my excavator?
A2: Give us correct model number/machine serial number/any numbers on the parts itself. Or measure the parts and give us dimension or drawing.
Q3: How about the payment terms?
A3: We usually accept T/T, L/C ,D/A,D/P,Money Gram ,Western Union, Paypal, Alibaba trade assurance.
Q4: What is your minimum order?
A4: It depends on what products you are buying. Normally, our minimum order is 20.
Q5: What is your delivery time?
A5: Usually,15-20 days. If the parts are available in our warehouse, our delivery time will be shortened to 7-10 days.
Q6: What about your Quality Control?
A6: We have a perfect QC system for the perfect products. A team who will detect the product quality and specification piece carefully, monitor every production process until packing is complete, to ensure products safety into the container.

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service:	Online Support
Warranty:	No
Type:	Sprocket
Application:	Excavator
Condition:	New
Video Outgoing-Inspection:	Not Available

Customization:	Available \| Customized Request

wheel sprocket

What are the Maintenance Requirements for a wheel sprocket Assembly?

Proper maintenance of the wheel sprocket assembly is essential to ensure its optimal performance and longevity. Here are some maintenance tips:

Regular Cleaning: Keep the wheel sprocket assembly clean from dirt, debris, and grime. Regularly wipe down the sprockets and chain to prevent buildup, which can lead to accelerated wear.
Lubrication: Apply a suitable lubricant to the chain and sprockets to reduce friction and wear. Lubrication also helps in maintaining smooth operation and preventing corrosion. However, avoid over-lubrication, as excessive grease can attract more dirt.
Chain Tension: Check the tension of the chain regularly. A loose chain can result in slippage and damage to the sprockets, while an overly tight chain can increase wear and strain on the components. Adjust the chain tension as per the manufacturer’s guidelines.
Inspection: Periodically inspect the sprockets and chain for signs of wear, damage, or elongation. Replace any worn-out or damaged components promptly to avoid further issues.
Alignment: Ensure proper alignment of the sprockets and wheels. Misalignment can lead to uneven wear and reduced efficiency. Adjust the alignment as needed to maintain smooth power transmission.
Replace Worn Parts: Over time, sprockets and chains will wear out due to regular use. Replace worn sprockets or chains with new ones from reputable suppliers to maintain optimal performance.
Environmental Considerations: In certain applications, exposure to harsh environments or extreme temperatures may require more frequent maintenance and inspection.

By following these maintenance practices, you can extend the lifespan of the wheel sprocket assembly and ensure reliable operation in various applications.

wheel sprocket

Special Considerations for Using a wheel sprocket System in Off-Road Vehicles

Off-road vehicles operate in rugged and challenging environments, which can put additional stress on the wheel sprocket system. Here are some special considerations to keep in mind when using a wheel sprocket system in off-road vehicles:

Material Selection: Choose high-quality materials for the wheel sprocket that can withstand rough terrains, impacts, and exposure to elements. Materials like hardened steel or alloys with good impact resistance are commonly used.
Sealing and Protection: Ensure that the wheel bearings and sprocket teeth are adequately sealed to prevent dirt, mud, water, and other debris from entering. Proper sealing helps to maintain smooth operation and prolong the lifespan of components.
Reinforcement: Consider reinforcing the wheel sprocket assembly if the vehicle will encounter heavy loads or extreme conditions. Reinforcements can add strength and durability to handle challenging off-road conditions.
Lubrication: Use a high-quality lubricant suitable for off-road conditions. Frequent lubrication is crucial to reduce friction, prevent corrosion, and protect components from wear and tear.
Regular Inspection: Off-road vehicles experience higher vibrations and shocks, leading to accelerated wear. Perform regular inspections to detect any signs of damage, misalignment, or wear. Address issues promptly to avoid further problems.
Shock Absorption: Consider incorporating shock-absorbing features or suspension systems to mitigate the impact on the wheel sprocket system during off-road driving. This helps to protect the components and improve overall vehicle performance.
Environmental Considerations: Off-road environments often expose the wheel sprocket system to dirt, sand, water, and other harsh elements. Choose coatings or treatments that offer corrosion resistance to protect against environmental damage.
Weight Consideration: Off-road vehicles may need to be lightweight to navigate difficult terrains effectively. Ensure the wheel sprocket components strike a balance between durability and weight to optimize vehicle performance.
Service and Maintenance: Establish a regular maintenance schedule and perform necessary servicing after each off-road trip. Cleaning, inspection, and replacement of worn parts are vital to ensure the system’s reliability.

By taking these special considerations into account, the wheel sprocket system in off-road vehicles can withstand the demands of rough terrains and provide reliable performance in challenging environments.

wheel sprocket

Choosing the Right Size of Sprocket to Match a Wheel

Choosing the correct size of sprocket to match a wheel is essential for ensuring efficient power transmission and proper functionality of a mechanical system. Here are the steps to help you choose the right size of sprocket:

1. Determine the Pitch Diameter of the Wheel:

Measure the diameter of the wheel from the center to the point where the teeth of the sprocket will engage with the wheel. This measurement is known as the pitch diameter of the wheel.

2. Identify the Desired Gear Ratio:

Determine the gear ratio you want to achieve for your application. The gear ratio is the ratio of the number of teeth on the sprocket to the number of teeth on the wheel and determines the speed and torque output.

3. Calculate the Number of Teeth on the Sprocket:

Once you have the pitch diameter of the wheel and the desired gear ratio, you can calculate the number of teeth on the sprocket using the formula:

Number of Teeth on Sprocket = (Desired Gear Ratio) * (Number of Teeth on Wheel)

4. Select a Standard Sprocket Size:

Based on the calculated number of teeth on the sprocket, choose a standard sprocket size that comes closest to the calculated value. Sprockets are available in various tooth counts, and you may need to choose the nearest size available.

5. Consider Chain Compatibility:

If you are using a chain drive system, ensure that the selected sprocket is compatible with the chain you plan to use. The chain pitch (distance between the centers of adjacent roller pins) should match the pitch of the sprocket.

6. Verify Center Distance:

Check that the center distance between the wheel and the sprocket is appropriate for your application. The center distance is the distance between the centers of the wheel and the sprocket and should be set to achieve the desired tension and alignment of the chain or belt.

7. Consider the Material and Tooth Profile:

Select a sprocket material suitable for your application, such as steel, stainless steel, or plastic, based on factors like load, environment, and operating conditions. Additionally, consider the tooth profile (standard or custom) to ensure smooth engagement with the chain or belt.

By following these steps and considering the specific requirements of your machinery and mechanical system, you can choose the right size of sprocket to match your wheel and achieve optimal performance and longevity of the system.

China OEM 500 Chain Sprocket Mini Excavator Crawler Undercarriage Spare Parts Track Bottom Roller Sprocket
editor by Dream 2024-05-10

China Good quality Factory Wholesale Cheap Price 428 Chain Front Rear Sprocket

Product Description

Factory Wholesale Cheap Price 428 Chain Front Rear Sprocket

Description:
Type : Coolster 125Cc Dirt Bike
Type : 428 Chain & Sprocket
Type : Rear Sprocket
Type : Chain Sprocket
Type : Motorcycle Rear Sprocket
Chian Size: 428 106Links
Front Sprocket
Tooth: 16T
Inside Diameter: 17mm
Mount hole spacing: 30mm

Rear Sprocket
Tooth: 56T
Inside Diameter: 52mm
Outside Diameter: 230mm
Mount hole spacing: 48mm
Bolt Diameter: 9mm

Fit 110cc 125cc 140cc PIT PRO PIT Bike Trail Bike Dirt Bike Thumpstar Pitpro Sunl Taotao ect.
Such as:
For Honda CR80R CR85R XR1pcs spark plugs per day.
Q3: How about your delivery time ?
A3: Delivery time is 20days after you confirmed order.
Q4: What is the benefit for the exclusive agency?
A4: 1.Market Protection
2.Special price or discount in some months
3.Priority delivery
4.Free promotion materials:T-shirt
Q7:Can you produce it with our sample?
A7:Yes ,we can.and we will make new mould according to your sample

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Certification:	CCC, CE
Name:	Sprocket
Color:	Same as in Photo
Sample:	Free Sample
Transport Package:	Cartonsbrand Inner Bag + Brand Small Box
Trademark:	TLZBMTL

Samples:	US$ 0/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \| Customized Request

wheel sprocket

Ensuring Proper Alignment between a Wheel and its Corresponding Sprocket

Proper alignment between a wheel and its corresponding sprocket is crucial for the smooth and efficient operation of the wheel sprocket system. Misalignment can lead to increased wear, noise, and reduced performance. Here are some steps to ensure proper alignment:

Use Precision Components: Ensure that both the wheel sprocket are high-quality, precision-manufactured components that meet the required specifications. Using well-machined components will aid in achieving better alignment.
Check Axle Alignment: Make sure the axle or shaft on which the wheel sprocket are mounted is straight and properly aligned. Any misalignment in the axle can lead to misalignment of the wheel sprocket.
Proper Mounting: Ensure that the wheel sprocket are securely and correctly mounted on the axle or shaft. Use appropriate fasteners and tightening techniques to prevent any movement or shifting during operation.
Check for Parallelism: The axes of the wheel sprocket should be parallel to each other. Measure the distance between the axes at multiple points to verify parallel alignment.
Use Alignment Tools: Alignment tools, such as laser alignment systems, can be employed to accurately align the wheel sprocket. These tools can help identify and correct misalignments effectively.
Check Tension and Tensioner Alignment: If a tensioner is used in the system, ensure that it is properly aligned and applying the right tension to the chain or belt. Incorrect tension can cause misalignment.
Regular Maintenance: Implement a regular maintenance schedule to check and adjust alignment as needed. Regular inspections can help identify and address alignment issues before they cause significant problems.
Monitor Performance: Keep an eye on the performance of the wheel sprocket system. Unusual noises, vibrations, or signs of wear can indicate misalignment and should be investigated promptly.

Proper alignment is essential for the long-term performance and reliability of the wheel sprocket system. By following these steps and conducting regular maintenance, you can ensure that the wheel sprocket work together harmoniously, providing efficient power transmission and minimizing wear and tear.

wheel sprocket

Choosing the Right Material for a Sprocket to Ensure Longevity

Choosing the right material for a sprocket is crucial to ensure its longevity and reliable performance in a given application. The material selection depends on various factors such as load, speed, operating environment, and budget. Here are some common materials used for sprockets and their considerations:

Steel: Steel sprockets are widely used in a wide range of applications due to their excellent strength, durability, and wear resistance. They are suitable for heavy-duty and high-speed operations. Different grades of steel, such as carbon steel or alloy steel, offer varying levels of hardness and strength.
Stainless Steel: Stainless steel sprockets are preferred when corrosion resistance is essential, making them suitable for applications where the sprocket is exposed to moisture, chemicals, or outdoor elements. They are commonly used in food processing, pharmaceutical, and marine industries.
Cast Iron: Cast iron sprockets offer good wear resistance and are often used in low to medium-speed applications. They are cost-effective and provide excellent performance in less demanding conditions.
Plastics: Plastic sprockets are lightweight and corrosion-resistant. They are commonly used in applications where low noise, self-lubrication, and resistance to chemicals or moisture are required. However, they have limited load-carrying capacity and may not be suitable for heavy-duty applications.
Aluminum: Aluminum sprockets are lightweight and commonly used in applications where weight reduction is critical, such as aerospace and certain machinery. However, they are not as durable as steel sprockets and are not suitable for high loads or harsh environments.

When choosing the right material for a sprocket, consider the following:

Load Capacity: Select a material that can handle the expected loads in the application without deforming or wearing excessively.
Speed: Higher speeds may require materials with better heat dissipation and wear resistance.
Environment: Consider factors such as moisture, chemicals, temperature, and outdoor exposure. Choose a material with suitable corrosion resistance and resilience to environmental conditions.
Maintenance: Some materials may require more frequent maintenance or lubrication to ensure longevity.
Cost: Balance the material’s performance with the budget constraints of the project.

It’s essential to consult with sprocket manufacturers or material experts to determine the most appropriate material for your specific application. They can provide valuable insights and recommendations based on your requirements, helping to ensure the longevity and optimal performance of the sprocket in your machinery or equipment.

wheel sprocket

Calculating Gear Ratio for a wheel sprocket Setup

In a wheel sprocket system, the gear ratio represents the relationship between the number of teeth on the sprocket and the number of teeth on the wheel. The gear ratio determines the speed and torque relationship between the two components. To calculate the gear ratio, use the following formula:

Gear Ratio = Number of Teeth on Sprocket ÷ Number of Teeth on Wheel

For example, if the sprocket has 20 teeth and the wheel has 60 teeth, the gear ratio would be:

Gear Ratio = 20 ÷ 60 = 1/3

The gear ratio can also be expressed as a decimal or percentage. In the above example, the gear ratio can be expressed as 0.3333 or 33.33%.

It’s important to note that the gear ratio affects the rotational speed and torque of the wheel sprocket. A gear ratio greater than 1 indicates that the sprocket’s speed is higher than the wheel’s speed, resulting in increased rotational speed and reduced torque at the wheel. Conversely, a gear ratio less than 1 indicates that the sprocket’s speed is lower than the wheel’s speed, resulting in decreased rotational speed and increased torque at the wheel.

The gear ratio is crucial in various applications where precise control of speed and torque is required, such as bicycles, automobiles, and industrial machinery.

China Good quality Factory Wholesale Cheap Price 428 Chain Front Rear Sprocket
editor by Dream 2024-05-09

China Hot selling CZPT Brand Wholesale Price China Industry Carbon Steel Stainless Plastic Conveyor Transmission 12b-1 12b-2 12b-3 Roller Chains with Sprocket for Machinery

Product Description

Product Description

Specification

Product Name	Wholesale Price Conveyor Chain 12b-2 Roller Chains with Sprocket For Machinery
Type	Roller Chain
MOQ	1meter
Brand	CHINAMFG
OEM	YES,We also can produce special chain according to your requirements,also produce matched sprocket/wheel.
Package	According to customer’s requirements
Weight	0.56kg/Meter
Delivery time	7 days

other models

Chain No.	P	h2	H	$	T
08AF29	12.700	10^)0	15.6	–	1.50
O8BF9O	12.700	10^0	17.0	0.3	1.60
0M-1STCF15	12.700	1571	17.0		1.60
10AF2	15.875	13.00	17.0	0.3	2.(0
10AF15	15.875	15.09	17.0	–	2.03
10AF23	15.875	13.00	2(18	0.3	2.03
10AF48	15«5	1100	16.9	«	2.03
10BF50	15B75	13.70	17.0	0.3	1.70
10AF5«	15^75	1SX)9	17.0	.	2.03

	P	h2	h	1	S	a
Chain No.
08BF25	12.7XJ	10.6	15.6	1.60		30,
08BF29	12. TO	1&6	14.5	1.60	as	30*
08BF30	12	1G6	14.5	l.g	Q3	30*
08BF35	12. W	ia6	21.5	1.60	0.6	30*
08BF67	12.TO	ia6	16.1	1.60	as	30*
0fflF195	12.70	10.6	45	1.60	0.4	30,
08AF10	12.70	10.6		L50	–	30*
12B-1STCF1	19.05	15.0	19.0	1.85	–	30,
12AF33	19.05	15.6	19.7	2.42	0£	18*

	P	hl	h2	h	A	Q
Chain No.
08BF21	12.7	10	1Q6	15.0	10	0

Company Profile
HangZhou Terry Machinery Co.Ltd is a leading supplier of bearings, Linear motion system for CNC , Ball transfer
Unit and transmission component .the growing industrial and Favorable policy of HangZhou benefit the developm
ent of Terry Machinery .Our products are utilized in industrial, motorcycle, vehicle and Automation applications.
Now we are exporting to 46 countries. including USA, GBR , Germany , Spain, Poland ,Turkey ect .The Goal o
f Terry Machinery to provide out customers with widest range of products at competitive prices, backed with the
best Service.OUR ADVANTAGE Products Our major products & Supplied:Meet all the international standards
and ISO9001 -TS1694 Certificate Big volume in Stock, No MOQ required Personnel Our salespersons are well
trained to accommodate your requests and speak English for your conveniences.Our technicians and engineers
Experience in the Industry area exceeds 23 years Service &Quality control ,We supply detailed drawings and
offer when ever necessary,We help all customers promote and improve their sales.We inspect every piece of
products by ourselves before delivery.

Application
related product
product-list-1.html
Packing &Delivery
Customer Praise
FAQ
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Standard Or Nonstandard:	Standard
Application:	Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car
Hardness:	Hardened Tooth Surface

Samples:	US$ 5.84/Piece 1 Piece(Min.Order) \| Order Sample

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost: Estimated freight per unit.	about shipping cost and estimated delivery time.

Payment Method:
	Initial Payment Full Payment

Currency:	US$

Return&refunds:	You can apply for a refund up to 30 days after receipt of the products.

transmission chain

How does the choice of chain attachment type affect the versatility of a transmission chain?

The choice of chain attachment type has a significant impact on the versatility and functionality of a transmission chain. Here’s a detailed answer to the question:

The attachment type refers to the specific design or configuration of the links or plates at the ends of the transmission chain. Different attachment types are available to accommodate various applications, equipment, and industry requirements. The selection of the right attachment type affects the chain’s versatility in the following ways:

1. Connection and Compatibility: The chain attachment type determines how the chain connects and interacts with other components in the system. It should be compatible with the equipment, sprockets, gears, or other mechanisms to ensure proper functioning and power transmission. Different attachment types may be required for different machinery or applications, such as conveyors, elevators, or industrial machinery.

2. Load Capacity and Strength: The attachment type influences the load capacity and strength of the transmission chain. Some attachment designs provide increased load-bearing capacity, allowing the chain to handle heavy loads or withstand high-torque applications. By choosing the appropriate attachment type, the chain’s versatility can be enhanced to suit a wide range of load requirements.

3. Flexibility and Adaptability: Certain attachment types offer greater flexibility and adaptability in terms of accommodating variations in equipment design or layout. They may allow for easier adjustment, tensioning, or lengthening of the chain to fit specific requirements. This flexibility enables the chain to be more versatile and adaptable to different configurations or changes in the operating environment.

4. Specific Application Requirements: Depending on the application, specific chain attachment types may be necessary to meet industry standards, safety regulations, or operational needs. For example, certain industries may require specialized attachments to ensure proper alignment, positioning, or engagement with specific components or materials. Choosing the appropriate attachment type ensures compliance with these requirements, enhancing the chain’s versatility for specific applications.

5. Easy Maintenance and Replacement: The choice of attachment type can also impact the ease of maintenance and replacement of the transmission chain. Some attachment designs allow for quick and convenient disassembly or replacement of damaged or worn-out chain links or plates. This facilitates efficient maintenance and reduces downtime, contributing to the overall versatility and reliability of the chain.

When selecting a transmission chain, it’s crucial to consider the specific attachment type required for the intended application. Factors such as load capacity, compatibility with equipment, ease of maintenance, and industry standards should be considered to ensure optimal versatility and performance of the transmission chain.

transmission chain

How does the choice of lubrication method impact the performance of a transmission chain?

The choice of lubrication method plays a crucial role in the performance and longevity of a transmission chain. Here’s a detailed answer to the question:

1. Reduced Friction and Wear: Proper lubrication ensures a thin film of lubricant between the moving parts of the transmission chain, reducing friction and minimizing wear. This helps to maintain the integrity of the chain’s components, such as pins, rollers, and bushings, by preventing metal-to-metal contact and reducing surface damage.

2. Heat Dissipation: Lubrication helps in dissipating heat generated during the operation of the transmission chain. By reducing friction and providing a cooling effect, the lubricant helps to prevent overheating, which can lead to premature wear, deformation, or failure of the chain.

3. Corrosion Protection: Lubricants often contain additives that offer corrosion protection to the transmission chain. These additives create a protective barrier against moisture, chemicals, and other corrosive elements, preventing rust formation and maintaining the chain’s performance in corrosive environments.

4. Noise Reduction: Adequate lubrication reduces the noise generated by the movement of the transmission chain. The lubricant acts as a cushion between the contacting surfaces, dampening vibrations and minimizing the noise levels produced during operation. This contributes to a quieter and smoother chain operation.

5. Extended Lifespan: Proper lubrication helps to extend the lifespan of the transmission chain. By reducing friction, wear, and the accumulation of debris, lubrication minimizes the stress on the chain’s components, resulting in improved durability and reduced likelihood of premature failure.

6. Operational Efficiency: A well-lubricated transmission chain operates with higher efficiency. With reduced friction, the chain experiences less power loss, enabling more effective power transmission. This leads to improved overall system efficiency, reduced energy consumption, and lower operating costs.

7. Contamination Prevention: Lubrication acts as a barrier, preventing contaminants, such as dust, dirt, and debris, from entering the chain’s components. This helps to maintain the cleanliness of the chain, reducing the risk of abrasive wear and preserving the integrity of its parts.

It’s important to consider the specific operating conditions, such as temperature, speed, load, and environment, when selecting the lubrication method for a transmission chain. Factors such as the viscosity, temperature range, and compatibility of the lubricant with the chain material should be taken into account to ensure optimal lubrication performance.

transmission chain

Are there specific lubrication requirements for transmission chains?

Yes, transmission chains typically require proper lubrication to ensure smooth operation, reduce wear, and prolong their service life. Here are some key points regarding lubrication requirements for transmission chains:

Clean and Adequate Lubrication: It is important to keep the chain adequately lubricated to minimize friction and wear between the chain components. Lubrication helps reduce heat generation and prevents metal-to-metal contact, which can lead to premature wear and failure.
Appropriate Lubricant Selection: Choosing the right lubricant is crucial for optimal chain performance. Factors to consider when selecting a lubricant include the application temperature, load conditions, speed, and environmental factors. Lubricants should have good adhesion properties, resist oxidation, and provide sufficient film strength to protect the chain surfaces.
Proper Lubrication Interval: Regular lubrication at appropriate intervals is necessary to maintain the chain’s performance and reduce the risk of excessive wear. The lubrication frequency depends on the operating conditions and the specific lubricant used. Manufacturers usually provide recommendations for lubrication intervals based on the chain type and application.
Effective Lubrication Application: Proper application of lubricant is essential to ensure uniform coverage and penetration into the chain components. The lubricant should be applied to the inner link plates, roller surfaces, and pin-bushing interfaces. Excess lubricant should be removed to prevent buildup and contamination.
Environmental Considerations: In certain environments, such as dusty or dirty conditions, the chain may require more frequent lubrication to prevent the ingress of contaminants and maintain proper lubrication film. Additionally, in high-temperature or high-speed applications, special high-temperature or high-speed lubricants may be necessary.
Regular Inspection and Maintenance: Along with proper lubrication, regular inspection and maintenance of the transmission chain are essential. This includes checking for signs of wear, lubricant degradation, and proper tension. Any damaged or worn components should be replaced promptly to prevent chain failure.

Following the manufacturer’s recommendations and adhering to the specific lubrication requirements for the transmission chain will help ensure optimal performance, reduce wear, and extend the chain’s lifespan.

China Hot selling CZPT Brand Wholesale Price China Industry Carbon Steel Stainless Plastic Conveyor Transmission 12b-1 12b-2 12b-3 Roller Chains with Sprocket for Machinery
editor by CX 2024-05-09

China high quality Motorcycle Transmission Chain X-Ring Super Heavy Duty X-Ring Chain with Connecting Link

Product Description

Product Parameters

Product Name	Motorcycle Gear & Chain Kit 530
Material	Alloy Steel
Chain NO	530
Pitch (mm)	12.7
Bush Type	CHINAMFG
Width(mm)	7.85
Pin Dia.(mm)	4.45
Pin Length(mm)	19.05
Roller Dia(mm)	8.51
Plate Thickness Inner(mm)	1.96
Plate Thickness Outer(mm)	1.96
Tensile Strength(kn)	20.6
Weight(kg/m)	0.85

Product Details

SFR Super O-Ring chain is a light-weight design of high-performance sealing chain, maintaining maximum strength while reducing the chain width and weight. The optimized O-ring overcomes the shortcomings of ordinary sealing chain, offering 150% lifespan of ordinary O-ring.
Silver outer + black inner, CHINAMFG outer + black inner colour configurations available. migh wear-resistant, maintenance-free lubrication , low cost O-rings

Product Packing

Semi-Automatic PET Bottle Blowing Machine Bottle Making Machine Bottle Moulding Machine PET Bottle Making Machine is suitable for producing PET plastic containers and bottles in all shapes.

Product Usage

SELECTION & INSTALLATION

We strongly recommends you to lubricate a new connecting link before connecting both ends of the new chain(Fig. B) Clip type connecting link (FJ,RJ) The open end of the clip must be set opposite the chain drive direction(Fig. C). FJ type connecting link has Press Fit Outer Plates that require SFR Cutting &Riveting Tool to press on the side plates. Rivet type connecting link(ZJ) Use MOTOMAX KM500R Cutting & Riveting Tool to press fit connecting link plates and precisely rivet pin head by flare dimensions we recommend. 5.For chain sag adjustment, follow the recommendation in motorcycle owner’s manual. Standard chain sag with the load of riders is 10 mm(Fig. D).

SELECTION & INSTALLATION

1.Be sure to consult your distributor / local dealer or check with SFR chain catalogue or application chart whether this chain and connecting link are applicable for your motorcycle. Improper selection and use may cause serious damage or injury.

2.Cut the old chain at its joint part. If your motorcycle came with an endless chain or a chain with Rivet type connecting link(ZJ), use SFR Cutting & Riveting Tool or similar cutting tool.

3.Fit the new chain to the end of the old one, using a new connecting link. By turning the rear wheel, the new chain will come in position(Fig. A)

Motorcycle Chain Handing Instructions

Drive chain is a critical safety part for motorcycle driving. To ensure safe drive, you are kindly requested to peruse and observe your motorcycle owner’s manual and the following instructions.

Company Introduction

SFR Chain Group has been pushing its way to the leading positions in the industrial chain industry since last century.

With stringent quality controls, we strive to exceed our customers’ expectations in terms of quality and service. Our products aresold to more than 80 countries in every industry that requires moving, conveying, lifting or transmitting power.

Our Services & Strength

With a monthly production output of over 2.2 million pieces, SFR motorcycle chain is the cornerstone of the group. As 1 of theWorld’s top manufacturers of motorcycle chain, we serve some of the largest brands in the automotive sector and within our widerange there is always a chain to go with every power and use, from urban mopeds to high powered racing motorbikes, dirt bikes orATV quads.

FAQ

SFR operates 4 fully owned factories and 1 joint venture, certified by ISO9001 and IATF 16949 Quality Management System. Ourcommitment to R&D led SFR to establish stable cooperation with several CHINAMFG universities and research institutes in China,as well as setting up an Intelligent Chain Drive Research Center within the group, altogether resulting in its more than 70
patents. This allows us to offer the widest range of power transmission and conveyor chain at the most competitive prices.We at SFR Chain always adhere to the group’s spirit of integrity, efficiency and innovation: “We strive to offer the best productsand service to our customers”.

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Warranty:	1 Year Guarantees
Type:	Motorcycle Chain
Material:	Alloy Steel
Certification:	ISO9001：2001, CE
Number of Row:	Single/Double/Triplex
Surface Treatment:	Zinc Plated, Gold Coated, Copper Coated

Samples:	US$ 5/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \| Customized Request

transmission chain

What are the benefits of using a corrosion-resistant material for a transmission chain?

Using a corrosion-resistant material for a transmission chain offers several advantages. Here’s a detailed answer to the question:

Corrosion-resistant materials, such as stainless steel or specialized coatings, provide the following benefits for transmission chains:

1. Enhanced Durability: Corrosion can significantly reduce the lifespan of a transmission chain by causing surface degradation, pitting, or rusting. By using a corrosion-resistant material, the chain’s durability is improved, allowing it to withstand exposure to harsh environments, chemicals, moisture, and temperature variations.

2. Extended Service Life: Corrosion-resistant materials help prevent or minimize the formation of rust or corrosion on the chain’s surface. This extends the chain’s service life, reducing the frequency of replacements and associated downtime and maintenance costs.

3. Reliable Performance: Corrosion can negatively impact the performance of a transmission chain by increasing friction, decreasing flexibility, and impairing the smooth engagement with sprockets or other components. Using a corrosion-resistant material ensures consistent and reliable performance, allowing the chain to operate smoothly and efficiently.

4. Reduced Maintenance: Corrosion-resistant transmission chains require less maintenance compared to chains made from non-corrosion-resistant materials. They are less prone to surface damage, require fewer lubrication intervals, and generally demand less attention to prevent deterioration. This results in reduced maintenance efforts and costs.

5. Suitable for Challenging Environments: Many industries and applications expose transmission chains to corrosive substances, moisture, humidity, or high temperatures. Using a corrosion-resistant material ensures that the chain can perform reliably in these challenging environments, such as marine, chemical processing, food processing, or outdoor applications.

6. Improved Safety: Corrosion can compromise the integrity and strength of a transmission chain, potentially leading to chain failure or unexpected equipment downtime. Utilizing a corrosion-resistant material helps maintain the chain’s structural integrity, reducing the risk of accidents, equipment failures, and associated safety hazards.

It’s important to consider the specific requirements of the application and the level of corrosion resistance needed when selecting a transmission chain material. Factors such as environmental conditions, temperature, exposure to chemicals, and industry standards should be taken into account to ensure optimal performance and longevity of the chain.

transmission chain

How does the choice of material impact the performance of a transmission chain?

The choice of material for a transmission chain plays a crucial role in its overall performance and durability. Here’s a detailed answer to the question:

1. Strength and Load Capacity: Different materials have varying levels of strength and load-carrying capacities. High-strength materials like alloy steel or stainless steel offer superior strength and can withstand heavy loads. The choice of a material with adequate strength ensures that the transmission chain can handle the required load without premature wear or failure.

2. Wear Resistance: The material used in the construction of a transmission chain affects its wear resistance. Some materials, such as hardened steel or certain alloys, have excellent wear resistance properties, allowing the chain to withstand abrasive conditions and prolong its lifespan. Choosing a material with good wear resistance reduces the need for frequent chain replacements and maintenance.

3. Corrosion Resistance: In environments where corrosion is a concern, such as outdoor or corrosive industrial settings, selecting a material with high corrosion resistance is essential. Stainless steel or specially coated chains offer excellent resistance to rust and corrosion, ensuring reliable performance and longevity even in harsh conditions.

4. Fatigue Strength: The material’s fatigue strength is crucial in applications where the transmission chain undergoes repeated cyclic loading. Fatigue failure can occur when a chain is subjected to continuous stress cycles, leading to cracks and eventual failure. Materials with high fatigue strength, such as specific alloys or heat-treated steels, are ideal for applications that require excellent fatigue resistance.

5. Temperature Resistance: The operating temperature of an application can impact the choice of material for a transmission chain. Some materials, such as heat-treated steels or specialized alloys, can withstand high-temperature environments without losing their mechanical properties. In contrast, certain plastics or polymers may be suitable for low-temperature applications. Choosing a material that can withstand the expected temperature range ensures optimal performance and prevents premature chain failure.

6. Cost Considerations: The choice of material also involves cost considerations. Some high-performance materials, such as stainless steel or specialized alloys, may have a higher initial cost compared to standard carbon steel chains. However, the increased performance, longevity, and reduced maintenance requirements provided by these materials may result in long-term cost savings.

It’s important to carefully assess the specific requirements of the application, including load capacity, environmental conditions, and operating parameters, when choosing the material for a transmission chain. Consulting with industry experts or manufacturers can help determine the most suitable material for optimal chain performance and longevity.

transmission chain

Can transmission chains be used in high-speed applications?

Yes, transmission chains can be used in high-speed applications, but there are certain considerations to take into account. Here’s a detailed explanation:

China high quality Motorcycle Transmission Chain X-Ring Super Heavy Duty X-Ring Chain with Connecting Link
editor by CX 2024-05-09

China Custom Manufacturer Roller Chains Protection Transmission Chain

Product Description

Factory Sale Chain Manufacturer Roller Quality Chains Protection Iso/Din 140 Transmission Chain

Products Description

Stainless steel chains are widely used in food processing, pharmaceutical, chemical production, rubber processing, non-ferrous metal smelting, electronic equipment, environmental protection equipment and heat treatment equipment and other fields of mechanical transmission and conveying equipment.

Traction chains are widely used in forklifts, CHINAMFG stackers, textile machinery, parking garages, drilling rigs, aerial work platforms, pipe benders, etc.

Drive chains are mainly used to transmit power and are widely used in agricultural machinery, construction machinery, escalator drive, logistics and packaging machinery industries.

Conveyor chain is widely used in food, wood and paper, logistics, packaging machinery, building materials machinery, environmental protection equipment and other industries for material conveying

Details Images

Agricultural Machinery Chain

Agricultural machinery chains are mainly used in rice, wheat, corn, cotton and other agricultural machinery to provide driving and conveying functions to realize the mechanization of the whole process of agricultural production from plowing, sowing to harvesting.

Conveyor chain

Conveyor chain products are characterized by high strength, wear resistance, high precision, corrosion resistance, temperature resistance, etc. to meet the needs of efficient, smooth and reliable conveying

Drive chains

The transmission chain adopts high-quality raw materials and advanced technology to develop a series of high-end chain transmission products with high wear resistance, high fatigue strength and high precision.

Product Paramenters

Transmission chain (Driving Chain)

Short Pitch Precision Roller Chain (A Series)(1,2,3)

04C-1 06C-1-2-3 085-1-2-3 08A-1-2-3 10A-1-2-3 12A-1-2-3 16A-1-2-3 20A-1-2-3 24A-1-2-3 28A-1-2-3 32A-1-2-3 40A-1-2-3 48A-1-2-3

-2 35-3 -2 40-3 50 50-2-50-3 60 60-2 60-3 80 80-2 80-3 100 100-2 100-3 120 120-2 120-3 140 140-2 160 160-2 180 200

200-2 240

Short Pitch Precision Roller Chain (B Series)(1,2,3)

06B-1-2-3 06B-1-2-3 08B-1-2-3 10B-1-2-3 12B-1-2-3 16B-1-2-3 20B-1-2-3 24B-1-2-3 28B-1-2-3 32B-1-2-3 40B-1-2-3 48B-1-2-3 56B-1-2-3

64B-1-2-3 72B-1-2-3

Heavy Duty Series Roller Chain(1,2)

08AH-1 10AH-1 12AH-1-2-3 16AH-1-2-3 20AH-1-2-3 24AH-1-2-3 28AH-1-2-3 32AH-1-2-3 40AH-1-2-3

Side Bow Chain

40SB 43SB 50SB 60SB 63SB 80SB 08BSB 08BSBY1 10BSB 12BSB C2050SB

Motorcycle Chain

H 420 420H 428 428H 520 520H 525 525H 530 530H 630 630H

Engine Mechanism Chain (Timing Chain)

CL04

Self-Lubrication Roller Chain

08BSLR 10BSLR 12BSLR 16BSLR 40SLR 50SLR 60SLR 80SLR

Double Pitch Transmission Chain

208A 208B 210A 210B 212A 212B 216A 216B 220A 220B

2100

Bush Chain

P15F-B P20-B P25-B P25F1-B P30F2-B P36-B P40-B P45-B P50-B P55-B P60-B P70-B P80-B

Company Profile

SFR Chain Group has been excelling at manufacturing and innovating motorcycle and industrial chain since 1991,always focusing on high quality and innovation to stay in the pole position of the industry.

SFR operates 4 fully owned factories and 1 joint venture, certified by ISO9002, ISO9001 and ISO/TS16949 Quality Management System.

SFR offers over 2000 series, which are exported to over 60 countries all over the World, and are widely used in variety of fields. Such as agricultural machines, motorcycles, metallurgy, wood processing, or food and beverage processing, among others. We at SFR Chain always adhere to the group’s spirit of integrity, efficiency and innovation:”We strive to offer the best products and service to our customers”

SFR is a global professional supplier focusing on chain drive solutions, with famous chain drive brands such as SFR, SUNFUN, MOTOMAX, EP and TVH.

Our commitment to R&D led SFR to establish atable cooperation with several ell-known universities and research institutes in China, as well as setting up an Intelligent Chain Drive Research Center within the group, altogether resulting in its more than 70 patents. This allows us to offer the widest range of power transmission and conveyor chain at the most competitive prices.

Since 1991, it has become a leading company in the chain industry with 5 production bases, about 110,000 square CHINAMFG of factory space, more than 180 patents, more than 2,000 chain varieties, more than 8,000 product specifications,exports to more than 80 countries worldwide. Products are widely used in many fields such as logistics and conveying, food industry, petroleum industry, engineering machinery, lifting equipment, packaging machinery processing, environmental protection equipment, tobacco machinery, etc.

Factory equipment

SFR will continue to increase the investment in manufacturing, R&D, follow the wave of Industry 4.0, continuously improve the company’s technology, product, marketing and brand power, enhance the company’s comprehensive strength, and provide customers with better chain drive solutions.

High-speed punching of industrial chain plates Automatic high-speed punching, high efficiency, high precision, and good sound insulation and environmental protection measures.

Motorcycle chain automatic assembly line The chain automatic assembly line integrates the processes of parts loading, chain assembly, automatic detection, pre-stretching, head riveting, and oiling to achieve the real automatic and efficient agricultural chain automatic assembly.

Automatic assembly line for agricultural chains Using the design of electromechanical integration, the mechanical mold and pneumatic and hydraulic parts are effectively combined together to realize the automatic assembly of complex structure chains.

Testing Machine

SFR Chain currently has 5 manufacturing plants covering over 50,000 square CHINAMFG and employing nearly 1,000 people. We bring in top talent and some of the manufacturing equipment used for manufacturing and inspection to provide the highest quality standards and create effective economies of scale.

Recommend Products

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Standard or Nonstandard:	Standard
Application:	Textile Machinery, Garment Machinery, Conveyer Equipment, Packaging Machinery, Electric Cars, Motorcycle, Food Machinery, Marine, Mining Equipment, Agricultural Machinery, Car
Surface Treatment:	Electroplating, Zinc Plating
Structure:	Roller Chain, Hollow Chain
Material:	Stainless Steel, Alloy
Type:	Roller Chain, Double Pitch Chain

Samples:	US$ 2/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \| Customized Request

transmission chain

How does the choice of chain attachment type affect the versatility of a transmission chain?

The choice of chain attachment type has a significant impact on the versatility and functionality of a transmission chain. Here’s a detailed answer to the question:

transmission chain

Can transmission chains be used in automotive or motorcycle applications?

Transmission chains can indeed be used in automotive and motorcycle applications. Here’s a detailed answer to the question:

Automotive and motorcycle applications often require reliable and efficient power transmission to transfer torque from the engine to the wheels. Transmission chains offer several advantages that make them suitable for these applications:

1. High Strength: Transmission chains are designed to handle high torque and power requirements, making them suitable for the demanding conditions of automotive and motorcycle power transmission systems.

2. Efficient Power Transfer: Transmission chains provide a direct and efficient means of transferring power from the engine to the wheels. They have low energy losses due to friction, allowing for effective power transmission and optimal performance.

3. Compact Design: Transmission chains have a compact design, making them suitable for the limited space available in automotive and motorcycle applications. They can be easily integrated into the drivetrain system without occupying excessive space.

4. Wide Speed Range: Transmission chains can operate effectively across a wide range of speeds, accommodating the varying speed requirements of automotive and motorcycle applications.

5. Versatility: Transmission chains can be used in various types of automotive and motorcycle transmissions, including manual transmissions, automatic transmissions, and final drive systems.

6. Durability: Transmission chains are built to withstand the demanding conditions of automotive and motorcycle applications. They are designed to resist wear, fatigue, and corrosion, ensuring long-lasting performance and reliability.

7. Cost-Effective: Transmission chains offer a cost-effective solution for power transmission in automotive and motorcycle applications. They are generally more affordable than alternative transmission systems.

It’s important to note that the specific design and requirements of the automotive or motorcycle transmission system should be considered when selecting a transmission chain. Proper maintenance, lubrication, and periodic inspection are also crucial to ensure the chain’s performance and longevity in these applications.

transmission chain

What are the key components of a transmission chain?

A transmission chain consists of several key components that work together to transmit power and motion efficiently. The main components of a transmission chain include:

Inner Plates: These are flat metal plates with holes or slots for connecting the other components of the chain.
Outer Plates: Similar to inner plates, outer plates provide additional strength and support to the chain.
Pins: The pins hold the inner and outer plates together, creating a flexible link between them. They play a crucial role in maintaining the integrity and functionality of the chain.
Bushings: Bushings are cylindrical components that fit into the holes of the inner and outer plates. They provide a smooth surface for the chain to rotate around the pins.
Rollers: Rollers are cylindrical elements that fit between the inner plates and the bushings. They reduce friction and enable smooth movement as the chain engages with the sprockets.
Solid Bushings (optional): In some transmission chains, solid bushings may be used instead of bushings with holes. Solid bushings provide additional strength and stability to the chain.
Sprockets: Sprockets are toothed wheels that engage with the rollers of the transmission chain. They transfer power and motion to the chain, enabling it to drive various machinery and equipment.

These components work together to form a continuous loop that transmits power from the driving sprocket to the driven sprocket, allowing the chain to transfer rotational motion and drive various mechanical systems.

China Custom Manufacturer Roller Chains Protection Transmission Chain
editor by CX 2024-05-09

China Custom Stainless Steel Maintenance Free Agricultural Machnery Conveyor Link Durable Transmission Roller Chain

Product Description

Company Profile

-HangZhou CHOHO Industrial Co., Ltd. was founded in 1999. Has become the leader of chain system technology, the first batch of natioal recognized enterprise technology center,national technology innovation demonstration enterprise,and the first A-share listed company in China’s chain drive industry.The securities code is 003033.
-CHOHO has 4 subsidiaries, including testing technology and international trading companies. has 4 factories in HangZhou, Thailand factory, ZheJiang R&D Center and Tokyo R&D Center. In addition, CHOHO ZHangZhoug Industrial zone is expected to be completed & put into operation next year.
-We specialized in producing all kinds of standard chains and special chains, such as Agricultural Chain, Sprocket, Chain Harrow, Tillage Parts,Rice Harvester Chain, GS38 Chain, Roller Chain, Automobile Chain, Motorcycle Chain Industrial Chain and so on.Our partners among world top enterprises, such as LOVOL,JOHN DEERE,NEW HOLLAND, CLASS,AGCO,DEUTZFAHR,HONDA, KUBOTA etc.

Production Capacity Equipment

By 2571,CHOHO has more than 2,700 sets of main production equipment and more than 600 sets of high-precision equipment,With the domestic advanced product laboratory and chain production assembly line, CHOHO has strong research and development and testing capabilities for high-end chain products.

Our Advantages

1. Any inquiry you make will be answered professionally within 6~8 hours.
2. Attaches great importance to product quality and approved by many global quality system certification,such as France, Norway, Germany.
3. Focused on Chain since 1999, have rich experience in Production.
4. High-quality workers,First-class advanced equipment,good quality control,advanced technology.
5. Be Good at Custom-Made Products, provide customized services for customers.
6. Participated in the drafting of 24 national and industrial standards such as chains.As of 2571-Mar, CHOHO has 180 authorized patents.
7. With the responsibility of “Providing high quality chain system with the same service life for the global locomotive industry”, have established a strong R&D team.

CHOHO has a natural brand awareness. As of January 2571, CHOHO has registered the “CHOHO” trademark in more than 60 countries, including the United States, Japan, the United Kingdom, France, Germany, Russia, Spain, Austria, Belgium, Bulgaria, Croatia, Czech Republic, Denmark, Finland, Greece , Hungary, Ireland, Italy, Netherlands, Poland, Portugal, Romania, Ukraine, Sweden, Australia, Algeria, Egypt, Kenya, Morocco, South Korea, Kazakhstan, Mongolia, Syria, Thailand, Pakistan, India, Brazil, Mexico, Colombia, etc.

Product Advantages

Certifications

CHOHO attaches great importance to product quality and approved by many global quality system certification, such as France, Norway, and Germany. Through the establishment of a sophisticated production management process and quality control system, the entire product process control is achieved. With the introduction of advanced production, processing, and testing equipment, CHOHO has internationally leading full-process quality control capabilities to provide customers with high-quality products.

Choho Provide Chain System Solutions for The Global Top 500 and The Enterprises in Various Fields Top 10!

Broad Customer Channels Market Continues to Develop!

CHOHO has been invited to participate in domestic & international agricultural machinery exhibitions, such as Hannover Messe, Bologna Fair, Canton Fair ,VIV ASIA and so on!

Packaging & Shipping

Packaging Details:

Chain+Plastic Bag+Neutral Box+Wooden case+Big Carton+Steel Pallets or Customization

FAQ

1. Are you manufacturer or trade Company?
We are a factory focused on producing and exporting Chain over 23 years,have a professional international trade team.
2. What terms of payment you usually use?
T/T 30% deposit and 70% against document, L/C at sight
3. What is your lead time for your goods?
Normally 30~45 days.Stock can be shipped immediately.
4. Do you attend any Show?
We attend Hannover show in Germany, EIMA in Italy, CHINAMFG in France, CIAME in China and many other Agricultural machinery shows.
5.Do you offer free samples?
Yes,we can.or you just bear the shipping cost.
6.Is OEM available?
Yes, OEM is available. We have professional designers to help you design.

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Usage:	Transmission Chain, Conveyor Chain, Dedicated Special Chain, Maintenance Free Chain
Material:	Stainless steel
Surface Treatment:	Polishing

Samples:	US$ 1/Meter 1 Meter(Min.Order) \| Order Sample Sample

Customization:	Available \| Customized Request

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost: Estimated freight per unit.	about shipping cost and estimated delivery time.

Payment Method:
	Initial Payment Full Payment

Currency:	US$

Return&refunds:	You can apply for a refund up to 30 days after receipt of the products.

conveyor

Can a conveyor chain be used in cleanroom environments?

Yes, conveyor chains can be used in cleanroom environments with proper selection and design considerations. Cleanroom environments require stringent control of airborne particles, such as dust, microbes, and contaminants, to maintain high levels of cleanliness. Here are some factors to consider when using a conveyor chain in a cleanroom:

1. Material Selection:

– Choose a conveyor chain made from materials that are compatible with cleanroom requirements. Stainless steel, plastic, or special coatings are commonly used for their clean and non-contaminating properties.

– Avoid materials that generate excessive particles or contaminants, such as certain types of lubricants or chain coatings.

2. Design Considerations:

– Design the conveyor chain system to minimize particle generation. This includes smooth surfaces, rounded edges, and avoiding areas that can trap or accumulate particles.

– Use sealed or enclosed chain designs to prevent the release of lubricants or contaminants.

– Consider the integration of additional features, such as covers or guards, to further protect the chain and prevent particle ingress.

3. Cleaning and Maintenance:

– Establish a cleaning and maintenance protocol specific to the cleanroom environment. This may include regular cleaning and sanitization procedures to maintain cleanliness standards.

– Use cleaning agents and procedures that are approved for cleanroom use and do not introduce contaminants.

– Regularly inspect the conveyor chain system for any signs of wear, damage, or contamination. Promptly address any issues to ensure the chain’s reliability and cleanliness.

4. Compliance with Cleanroom Standards:

– Ensure that the conveyor chain system meets the cleanliness and particle generation requirements of the specific cleanroom standards or classifications in which it will be used.

– Comply with relevant industry guidelines and regulations, such as ISO standards, when selecting and using conveyor chains in cleanroom environments.

By considering these factors and implementing proper material selection, design considerations, cleaning protocols, and compliance with cleanroom standards, a conveyor chain can be effectively used in cleanroom environments while maintaining the required cleanliness levels.

conveyor

How do you prevent corrosion in conveyor chains?

Preventing corrosion in conveyor chains is essential for maintaining their performance and prolonging their lifespan. Here are some effective measures to prevent corrosion:

1. Material Selection: Choose conveyor chains made from corrosion-resistant materials such as stainless steel, plastic, or coatings specifically designed to resist corrosion. These materials offer better protection against rust and corrosion compared to standard steel chains.

2. Proper Lubrication: Apply a suitable lubricant to the conveyor chain regularly. Lubrication creates a protective barrier that helps prevent moisture and contaminants from reaching the metal surface, reducing the risk of corrosion. Select a lubricant that provides corrosion protection properties and is compatible with the chain material.

3. Environmental Controls: Control the operating environment to minimize exposure to corrosive elements. Implement measures such as humidity control, proper ventilation, and protection from direct contact with water or chemicals. Consider using covers or enclosures to shield the conveyor chain from environmental factors that can accelerate corrosion.

4. Surface Treatments: Apply corrosion-resistant coatings or treatments to the conveyor chain. These coatings can provide an additional protective layer that acts as a barrier against moisture and corrosive substances. Examples of surface treatments include zinc plating, galvanizing, or epoxy coatings.

5. Regular Inspections and Cleaning: Regularly inspect the conveyor chain for signs of corrosion or damage. Remove any accumulated dirt, debris, or corrosive substances promptly. Cleaning the chain helps prevent the buildup of contaminants that can accelerate corrosion.

6. Preventive Maintenance: Implement a preventive maintenance program that includes regular cleaning, lubrication, and inspection of the conveyor chain. This proactive approach helps identify and address any potential corrosion issues early on, preventing further damage.

7. Proper Storage: When not in use, store the conveyor chains in a dry and controlled environment. Protect them from exposure to moisture, humidity, and corrosive substances. Use appropriate storage methods, such as hanging the chains or storing them in sealed containers.

By following these preventive measures, you can significantly reduce the risk of corrosion in conveyor chains, ensuring their optimal performance and longevity.

conveyor

What are the common causes of conveyor chain failures?

Conveyor chain failures can occur due to various reasons, and identifying the root cause is crucial for preventing future issues. Here are some common causes of conveyor chain failures:

Lack of Lubrication: Insufficient or improper lubrication can lead to increased friction and wear on the chain components, resulting in premature failure.
Excessive Load: Overloading the conveyor chain beyond its rated capacity can cause excessive stress and strain, leading to chain elongation, deformation, or link breakage.
Misalignment: Improper alignment of the conveyor chain can cause uneven loading and excessive wear on specific areas, leading to chain failure.
Environmental Factors: Harsh operating environments, such as high temperatures, corrosive substances, or abrasive materials, can accelerate chain wear and corrosion, leading to failure.
Foreign Objects: The presence of foreign objects or debris on the conveyor system can interfere with the movement of the chain, causing jamming, binding, or chain damage.
Poor Maintenance: Inadequate maintenance practices, such as irregular inspections, failure to address minor issues promptly, or neglecting to replace worn components, can contribute to chain failures.
Incorrect Installation: Improper installation, including incorrect tensioning, misalignment, or using incompatible components, can result in premature chain failure.
Fatigue and Wear: Continuous operation over time can lead to fatigue and wear in the chain, especially in high-speed or heavy-duty applications, resulting in eventual failure.

Regular maintenance, proper lubrication, adequate training for operators, and adherence to manufacturer guidelines can help mitigate these common causes of conveyor chain failures. Conducting routine inspections, promptly addressing issues, and replacing worn components can also significantly extend the life of the conveyor chain.

China Custom Stainless Steel Maintenance Free Agricultural Machnery Conveyor Link Durable Transmission Roller Chain
editor by CX 2024-05-09

China factory Bicycle Chain Cleaner Set Tensioner Remover Brush Bracelet Lock Protector Machine Wheel Drive Cleaning Kit Plaststic Breaker Frame Lock Chain

Product Description

Bicycle Chain Cleaner Set Tensioner Remover Brush Bracelet Lock Protector Machine Wheel Drive Cleaning Kit Plaststic Breaker Frame Lock Chain

Product Description

The chain types are divided into engineering chain, conveying chain, plate chain, transmission chain, escalator chain, parking equipment chain, agricultural chain, stainless steel chain, etc. There are different types of chains with different purposes, specifications, models and styles.

Plate chain type Plate chain is usually used to lift goods. For example, forklift, lifting machinery and equipment. Plate chain has no rollers, but chain plates are connected with each other. It is a kind of chain used for loading. Different types of plate chains have different functions,	Stainless steel chain Stainless steel chain types include standard stainless steel chain, stainless steel hollow pin chain, stainless steel chain used for environmental protection equipment, etc,
Type of transmission chain Many types of transmission chains are power transmission chains, such as precision roller chains, double pitch roller chains, high-strength short pitch precision roller chains, petroleum chains, pumping unit chains, self-lubricating roller chains, side bending (turning machine) chains, corrosion resistant chains, etc	There are many types of escalator chains, including escalator step chains, heavy-duty high gradient escalator step chains, travelator chains, and escalator chains of different specifications and models,
The engineering chain includes many kinds of chains, such as cement bucket elevators, environmental protection equipment, pavers, trenchers, welding equipment, mining, power plant dust removal and other equipment.	Agricultural machinery chain Agricultural machinery chain is a chain developed and produced according to the characteristics of different crops, including rice harvester chain, GS38 combine chain, corn harvester chain, citrus straw harvester chain, soybean harvester chain, peanut harvesting chain, garlic sowing chain, and potato planter chain.
There are many types of conveying chains, such as wood conveying chain, double speed chain, RF conveying chain, sharp tooth chain, sugar chain, brown oil chain, F chain, metric conveying chain, top roller conveying chain, grain scraper, hollow pin, suspension conveying, etc. The conveying chain is a power chain for transporting goods.	Parking equipment chain This type of chain includes roller chains for parking equipment, chains for vertical circulation parking equipment, and parking equipment chains that can be developed according to demand.

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Usage:	Transmission Chain, Drag Chain, Conveyor Chain, Dedicated Special Chain
Material:	Stainless steel
Surface Treatment:	Oil Blooming
Feature:	Oil Resistant
Chain Size:	1/2"*3/32"
Structure:	Roller Chain

Samples:	US$ 9999/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \| Customized Request

drive chain

What are the benefits of using a maintenance-free drive chain?

Using a maintenance-free drive chain offers several advantages in applications where minimal maintenance and high reliability are desired. Here is a detailed explanation:

A maintenance-free drive chain, also known as a self-lubricating chain, is designed to operate without the need for regular lubrication or maintenance. The benefits of using such a chain include:

Reduced Downtime: Maintenance-free drive chains eliminate the need for regular lubrication and associated maintenance tasks. This saves time and reduces the frequency of equipment shutdowns for lubrication and maintenance, resulting in increased productivity and reduced downtime.
Lower Maintenance Costs: Maintenance-free chains require less maintenance, which leads to cost savings. There is no need for purchasing lubricants, scheduling routine maintenance, or performing frequent lubrication tasks. This can result in significant cost savings over the life of the chain.
Increased Reliability: Maintenance-free chains are designed to provide reliable and consistent performance over extended periods without the need for lubrication. They are constructed using self-lubricating materials or have built-in lubrication systems, ensuring optimal chain operation and minimizing the risk of chain failure due to inadequate lubrication.
Extended Service Life: Maintenance-free chains are often engineered with materials that exhibit excellent wear resistance and self-lubricating properties. This extends the chain’s service life by reducing wear, elongation, and the need for frequent replacements. The chains maintain their performance characteristics even in demanding environments.
Cleaner Operation: Maintenance-free chains do not require external lubrication, which eliminates the risk of lubricant splatter or contamination. This is particularly beneficial in applications where cleanliness is essential, such as food processing, pharmaceuticals, or cleanroom environments. The absence of lubrication also reduces the attraction of dust or debris, contributing to cleaner and more reliable operation.
Environmentally Friendly: Maintenance-free chains can contribute to environmental sustainability. The elimination of routine lubrication reduces the consumption of lubricants and minimizes the release of lubricants into the environment. This aligns with eco-friendly practices and reduces the overall environmental impact of the equipment.
Application Versatility: Maintenance-free chains can be used in various industries and applications where minimal maintenance is desired or where lubrication is challenging or not feasible. They find applications in industries such as food processing, packaging, automation, automotive, and many others.

It is important to note that while maintenance-free chains offer many benefits, they still require regular inspection and occasional cleaning to ensure optimal performance and detect any abnormal wear or damage.

When selecting a maintenance-free chain, it is crucial to consider factors such as load capacity, speed, environmental conditions, and compatibility with the specific application requirements.

By utilizing maintenance-free drive chains, operators can benefit from reduced downtime, lower maintenance costs, increased reliability, extended service life, cleaner operation, environmental friendliness, and application versatility.

drive chain

Can a drive chain be used in a medical or healthcare application?

Yes, a drive chain can be used in certain medical and healthcare applications where reliable and precise power transmission is required. Here is a detailed explanation:

In medical and healthcare settings, various equipment and devices rely on efficient power transmission to perform critical functions. While drive chains may not be used in all medical applications, they can be suitable for specific applications that involve controlled movement, precision, and durability. Here are some examples:

Medical Imaging Systems: Drive chains can be used in medical imaging systems such as CT scanners, MRI machines, and X-ray machines. These systems often require precise and synchronized movement of components for image acquisition. Drive chains enable accurate positioning and controlled motion, ensuring the necessary alignment and stability during the scanning process.
Robotic Surgery Systems: Robotic surgery systems require precise and reliable power transmission to control the movement of robotic arms and surgical instruments. Drive chains can be used to transmit power and ensure accurate positioning, enabling surgeons to perform delicate procedures with enhanced precision and control.
Rehabilitation and Physical Therapy Equipment: Drive chains can be incorporated into rehabilitation and physical therapy equipment such as exercise machines or motorized devices used for therapeutic purposes. These chains allow for adjustable resistance, controlled movement, and precise range of motion, assisting patients in their recovery and rehabilitation processes.
Medical Equipment Mobility: Drive chains can be utilized in medical equipment such as hospital beds, stretchers, or mobile carts, where controlled and smooth movement is necessary. Drive chains enable adjustable height, positioning, and mobility, ensuring safe and precise patient handling and transport within healthcare facilities.

It is important to note that in medical and healthcare applications, specific regulations, standards, and guidelines must be followed. The design, material selection, and installation of drive chains should comply with the applicable medical industry standards and safety requirements.

Additionally, regular maintenance, including inspection, lubrication, and tension adjustment, is crucial to ensure optimal performance and reliability of the drive chain in medical and healthcare applications.

By utilizing drive chains in select medical and healthcare applications, operators can benefit from precise power transmission, accurate positioning, controlled movement, and enhanced functionality, contributing to improved patient care and medical outcomes.

drive chain

Can a drive chain be used in environments with high temperatures?

Yes, a drive chain can be used in environments with high temperatures, but there are certain considerations to keep in mind. Here’s an explanation:

Drive chains can operate in high-temperature environments, but the selection of the appropriate chain and proper maintenance practices are crucial for ensuring their performance and longevity:

1. Heat-Resistant Materials: When operating in high-temperature environments, it is important to choose a drive chain made from heat-resistant materials. High-grade steel alloys or specialized heat-resistant materials may be used to ensure the chain can withstand the elevated temperatures without significant degradation.
2. Lubrication: Proper lubrication is essential to reduce friction and wear, particularly in high-temperature environments. It is crucial to select lubricants specifically designed for high-temperature applications that can withstand the heat without breaking down or evaporating too quickly. Regular lubrication and inspection are necessary to maintain the lubricant’s effectiveness.
3. Heat Dissipation: Ensuring proper heat dissipation is important to prevent overheating of the chain. Adequate ventilation or cooling measures should be implemented, if necessary, to keep the chain operating within a safe temperature range.
4. Maintenance: Regular inspection and maintenance are crucial in high-temperature environments. Periodic checks for signs of wear, elongation, or damage should be performed. Proper tension adjustment and alignment should be maintained to prevent excessive stress and wear on the chain.
5. Operating Conditions: Consider other factors associated with high-temperature environments, such as exposure to chemicals, contaminants, or extreme temperature fluctuations. These factors may affect the chain’s performance and longevity, and additional measures may be required to ensure optimal operation.

It is important to consult the manufacturer’s guidelines and specifications to ensure that the selected drive chain is suitable for the specific high-temperature environment. By selecting the appropriate chain and implementing proper maintenance practices, a drive chain can effectively operate in high-temperature environments while maintaining performance and durability.

China factory Bicycle Chain Cleaner Set Tensioner Remover Brush Bracelet Lock Protector Machine Wheel Drive Cleaning Kit Plaststic Breaker Frame Lock Chain
editor by CX 2024-05-09

China supplier Hardened Tooth Surface C45 Sea/Plywood Case Industrial Chain Sprocket Sprockets

Product Description

ZHangZhoug CZPT Machinery Co., Ltd
(DIN/ANSI/JIS Standard or made to drawing)
Product Description:

Detailed Photos:

Company Profile:

ZHangZhoug CZPT Machinery Co., Ltd. Is the vice chairman of chain Transmission Branch of China Machinery General parts Industry Association and a member of China chain Transmission Standardization Technical Committee.

Founded in 1954, mainly engaged in sprocket, gear, timing belt pulley, coupling production and sales, It is a large sprocket manufacturing enterprise in China, and it is also 1 of the largest standard sprocket manufacturers in the world at present. The product structure of the company has been developed from the single pattern of standard sprocket to non-standard transmission parts. Products are mainly sold in North America, South America, Europe, Africa and Japan, South Korea, the Middle East, Russia and Southeast Asia and other countries and regions, sales network all over the world.

The company has passed ISO 9002 quality assurance system certification for the first time in 1999, ISO9001: 2000 quality management system certification in 2003, ISO/TS16949 quality management system certification for the first time in 2009, ISO14001: 2004 environmental management system certification for the first time in 2571, ISO14001: 2015 environmental management system certification for 2017, and ISO9001: 2015 and IATF16949: 2016 quality management system certification for 2018. It lays a CZPT foundation for perfecting the internal management of the enterprise and opening up the external market.

The company adheres to the business philosophy of “Quality is life, technology is physique, delivery is moral, quantity is credit, service is kindred, cost is lifetime”, implementing “innovation-driven, twinning integration” upgrading strategy, promoting chain transmission products to excellence, and making every effort to create “harmonious cenfit, good quality cenfit, hundred years of cenfit”

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Standard Or Nonstandard:	Standard
Application:	Motor, Machinery, Agricultural Machinery, Car
Hardness:	Hardened Tooth Surface
Manufacturing Method:	Rolling Gear
Toothed Portion Shape:	Spur Gear
Material:	C45

Customization:	Available \| Customized Request

wheel sprocket

What are the Maintenance Requirements for a wheel sprocket Assembly?

Proper maintenance of the wheel sprocket assembly is essential to ensure its optimal performance and longevity. Here are some maintenance tips:

Regular Cleaning: Keep the wheel sprocket assembly clean from dirt, debris, and grime. Regularly wipe down the sprockets and chain to prevent buildup, which can lead to accelerated wear.
Lubrication: Apply a suitable lubricant to the chain and sprockets to reduce friction and wear. Lubrication also helps in maintaining smooth operation and preventing corrosion. However, avoid over-lubrication, as excessive grease can attract more dirt.
Chain Tension: Check the tension of the chain regularly. A loose chain can result in slippage and damage to the sprockets, while an overly tight chain can increase wear and strain on the components. Adjust the chain tension as per the manufacturer’s guidelines.
Inspection: Periodically inspect the sprockets and chain for signs of wear, damage, or elongation. Replace any worn-out or damaged components promptly to avoid further issues.
Alignment: Ensure proper alignment of the sprockets and wheels. Misalignment can lead to uneven wear and reduced efficiency. Adjust the alignment as needed to maintain smooth power transmission.
Replace Worn Parts: Over time, sprockets and chains will wear out due to regular use. Replace worn sprockets or chains with new ones from reputable suppliers to maintain optimal performance.
Environmental Considerations: In certain applications, exposure to harsh environments or extreme temperatures may require more frequent maintenance and inspection.

By following these maintenance practices, you can extend the lifespan of the wheel sprocket assembly and ensure reliable operation in various applications.

wheel sprocket

Vertical Power Transmission with wheel sprocket System

Yes, a wheel sprocket system can be used for vertical power transmission. In such cases, the system is designed to transmit power and motion between vertically aligned shafts. Vertical power transmission using a wheel sprocket assembly follows similar principles to horizontal transmission, but there are some factors to consider:

Load and Torque: When transmitting power vertically, the weight of the load can significantly impact the torque requirements. The torque must be sufficient to lift the load against gravity while accounting for friction and other resistive forces.
Sprocket Selection: Choosing the right sprocket is critical for vertical transmission. The sprocket teeth must be designed to engage the chain or belt effectively and prevent slipping, especially when lifting heavy loads.
Lubrication: Proper lubrication is essential to reduce friction and wear in the system. Vertical applications may require specific lubricants to ensure smooth operation and prevent premature failure.
Tensioning: Maintaining the correct tension in the chain or belt is crucial for vertical power transmission. Proper tension helps prevent sagging and ensures proper engagement between the wheel sprocket.
Overhung Load: In vertical setups, the weight of the sprocket and shaft assembly can impose an overhung load on the bearings. Adequate support and bearing selection are necessary to handle this load.

Vertical power transmission with a wheel sprocket system is commonly used in various applications, including conveyor systems, elevators, and some industrial machinery. Proper design, installation, and maintenance are essential to ensure safe and efficient operation in vertical configurations.

wheel sprocket

How Does a wheel sprocket Assembly Transmit Power?

In a mechanical system, a wheel sprocket assembly is a common method of power transmission, especially when dealing with rotary motion. The process of power transmission through a wheel sprocket assembly involves the following steps:

1. Input Source:

The power transmission process begins with an input source, such as an electric motor, engine, or human effort. This input source provides the necessary rotational force (torque) to drive the system.

2. Wheel Rotation:

When the input source applies rotational force to the wheel, it starts to rotate around its central axis (axle). The wheel’s design and material properties are essential to withstand the applied load and facilitate smooth rotation.

3. Sprocket Engagement:

Connected to the wheel is a sprocket, which is a toothed wheel designed to mesh with a chain. When the wheel rotates, the sprocket’s teeth engage with the links of the chain, creating a positive drive system.

4. Chain Rotation:

As the sprocket engages with the chain, the rotational force is transferred to the chain. The chain’s links transmit this rotational motion along its length.

5. Driven Component:

The other end of the chain is connected to a driven sprocket, which is attached to the component that needs to be powered or driven. This driven component could be another wheel, a conveyor belt, or any other machine part requiring motion.

6. Power Transmission:

As the chain rotates due to the engagement with the sprocket, the driven sprocket also starts to rotate, transferring the rotational force to the driven component. The driven component now receives the power and motion from the input source via the wheel, sprocket, and chain assembly.

7. Output and Operation:

The driven component performs its intended function based on the received power and motion. For example, in a bicycle, the chain and sprocket assembly transmit power from the rider’s pedaling to the rear wheel, propelling the bicycle forward.

Overall, a wheel sprocket assembly is an efficient and reliable method of power transmission, commonly used in various applications, including bicycles, motorcycles, industrial machinery, and conveyor systems.

China supplier Hardened Tooth Surface C45 Sea/Plywood Case Industrial Chain Sprocket Sprockets
editor by Dream 2024-05-09